manualshive.com logo in svg

NEC Express5800/53La, User Manual, Page: 122 / 314

Share
Download
NEC Express5800/53La User Manual Download Page 122

5-2  Installing the Operating System with Express Setup

About Express Setup

"Express Setup" helps you to install the Windows Operating System. The setup automatically
configures the RAID System and installs the Operating System and some management software.

IMPORTANT:

 Executing the Express Setup erases all data on the

hard disk drive.

You can also use "Parameter File" at "Express Setup" in order to save or backup parameters for
installation.
If you want to set up the workstation as before, execute the Express Setup with the parameter file
you have saved before.

NOTES:

„

 

If you want to create a parameters file, have a blank floppy disk
(MS-DOS 1.44MB format) ready.

„

 

When using a floppy disk, a USB floppy disk drive is required.

„

 

If you want to use the drivers located on the "OEM-Disk for Mass
Storage Device" that ships with optional boards, a parameters file
is mandatory.

„

 

You can create a parameters file in advance using "Parameter File
Creator" included in NEC EXPRESSBUILDER.

Summary of Contents for Express5800/53La



























































































































































































































































































































Reviews:

No comments