manualshive.com logo in svg

NEC Express5800/53La, User Manual, Page: 200 / 314

Share
Download
NEC Express5800/53La User Manual Download Page 200

8-6  Troubleshooting

Error
code

Error message

Recommended Action

0B62

DIMM3 has been disabled

0B63

DIMM4 has been disabled

0B6F

DIMM with error is enabled

0B70

The error occurred during
temperature sensor reading

0B71

System temperature out of the
range

Power off the workstation and remove the dust from the
fan if clogged. If the same error persists, contact your
service representative.

0B74

The error occurred during voltage
sensor reading

0B75

System voltage out of the range

0B78

The error occurred during fan
sensor reading

0BB1

SMBIOS - SROM data checksum
bad.

Contact your service representative.

Expansion ROM not initialized

Run BIOS SETUP, select [Advanced] - [PCI
Configuration] - [Option ROM Scan], and change
parameter to "Disabled" for the unbootable PCI board.

Invalid System Configuration Data
PCI System Error on Bus/Device/Function
PCI Parity Error on Bus/Device/Function
Resource Conflict
System Configuration Data Read error
System Configuration Data Write error
WARNING: IRQ not configured

Contact your service representative.

Summary of Contents for Express5800/53La



























































































































































































































































































































Reviews:

No comments