NEC Express5800/53La User Manual Download Page 176

Page: 176 / 314

6-18 Installing and Using Utilities

NEC ExpressUpdate Agent

The NEC ExpressUpdate Agent enables you to control the version of the firmware and software that
are installed on the server.

Using the NEC ESMPRO Manager, you can download update packages automatically and install
them simply without terminating the system.

Refer to "Installation Manual" in the NEC EXPRESSBUILDER for more information about an
installation and functions of the NEC ExpressUpdate Agent.

IMPORTANT:

To get the information of the update package which

does not support NEC ExpressUpdate, please refer to the web site
below.

http://www.nec.com/global/prod/express/index.html

Summary of Contents for Express5800/53La



























































































































































































































































































































Search results

Summary of Contents for Express5800/53La

Reviews:

NEC Express5800/53La, User Manual, Page: 176 / 314

Search results

Summary of Contents for Express5800/53La

Reviews: