NEC Express5800/53La User Manual Download Page 127

Page: 127 / 314

Installing the Operating System with Express Setup 5-7

Flow of Setup

Loading parameters (Step 2)

Select the operating system (Step 3)

RAID configuration (Step 4)

Windows Confirm Setting / Input
(Steps 5 to 10)

Save parameters (Step 11)

Start Express Setup (Step 12)

RAID Configuration

Perform

Create the OS partition / format

Copying Windows driver

↓

Copying Selected Application

Remove the Floppy Disk and CD/DVD-ROM
from the Drive

Insert Windows DVD-ROM

The installation is completed.

: Process that needs to input or select

: Process that proceeds automatically

Skip

Install OS Automatically

Agree Software License Agreement

Log on

Summary of Contents for Express5800/53La



























































































































































































































































































































Search results

Summary of Contents for Express5800/53La

Reviews:

NEC Express5800/53La, User Manual, Page: 127 / 314

Search results

Summary of Contents for Express5800/53La

Reviews: