manualshive.com logo in svg

NEC Express5800/53La, User Manual, Page: 110 / 314

Share
Download
NEC Express5800/53La User Manual Download Page 110

4-38  Configuring Your Workstation

Setting Hot Spare

Install a hard disk drive

Run LSI Software RAID Configuration Utility

Set for hot spare.

Exit LSI Software RAID Configuration Utility

 

1. 

Install a hard disk drive to be used as hot spare, and then turn on the workstation.

 

2. 

Run LSI Software RAID Configuration Utility.

 

3. 

Select [Objects] 

→

 [Physical Drive] from the TOP menu.

The [Objects - PHYSICAL DRIVES SELECTION MENU] screen appears.

 

4. 

Move the cursor onto the hard disk drive to be used as hot spare and press 

Enter

.

 

5. 

The [Port #X] screen appears. Select [Make HotSpare].

 

6. 

A confirmation screen appears. Select [Yes].

The hard disk drive indication is changed to [HOTSP].

Summary of Contents for Express5800/53La



























































































































































































































































































































Reviews:

No comments