manualshive.com logo in svg

NEC Express5800/53La, User Manual, Page: 235 / 314

Share
Download
NEC Express5800/53La User Manual Download Page 235

Upgrading Your Workstation  9-15

Configuration of RAID System using Onboard RAID Controller (SATA)

The workstation is equipped an Onboard RAID Controller on its mother board to configure a RAID
system.

At least two hard disk drives are required to configure the RAID system. Use the "LSI Software
RAID Configuration Utility" installed in Onboard RAID Controller to configure the RAID system.

IMPORTANT:

 Use two hard disk drives of the same capacity and

revolution.

The Onboard RAID Controller supports RAID0 (striping) and RAID1 (mirroring).

RAID0

In RAID0, data to be recorded is distributed to hard disk drives. The mode is called "striping".

In the figure below, data is recorded in stripe 1 (hard disk drive 1), stripe 2 (hard disk drive 2), and
stripe 3 (hard disk drive 3)… in the order. Because RAID0 allows all hard disk drives to be accessed
collectively, it can provide the best disk access performance.

IMPORTANT: 

RAID0 does not have data redundancy. When a hard

disk drive failure occurs, data cannot be restored.

RAID Controller

Hard disk

drive 1

Hard disk

drive 2

Stripe 1

Hard disk

drive 3

Stripe 4

Stripe 2

Stripe 5

Stripe 3

Stripe 6

Summary of Contents for Express5800/53La



























































































































































































































































































































Reviews:

No comments