NEC Express5800/53La User Manual Download Page 270

Page: 270 / 314

D-12 Installing Windows 7

Insert the "OEM-Disk" into the USB floppy disk drive, and click [Browse].

IMPORTANT:

If you have created "OEM-Disk" into the Flash FDD,

connect the Flash FDD.

NOTES:

In case of Installing Windows 7 Professional 64-bit (x64) Edition:
Set the [Windows 7 x64 Edition OEM-Disk for
EXPRESSBUILDER].

In case of Installing Windows 7 Professional 32-bit (x86) Edition:
Set the [Windows 7 OEM-Disk for EXPRESSBUILDER].

[Browse for Folder] window is displayed:

<Windows 7 Professional 64-bit (x64) Edition>
Select <drive letter>:\OEM-Disk\win7x64\megasr1, and click [OK].

<Windows 7 Professional 32-bit (x86) Edition>
Select <drive letter>:\OEM-Disk\win7\megasr1, and click [OK].

Select [LSI Embedded MegaRAID] and click [Next].

Read the license terms carefully. If you agree, select [I accept the license terms], and then
click [Next].

Summary of Contents for Express5800/53La



























































































































































































































































































































Search results

Summary of Contents for Express5800/53La

Reviews:

NEC Express5800/53La, User Manual, Page: 270 / 314

Search results

Summary of Contents for Express5800/53La

Reviews: