manualshive.com logo in svg

NEC Express5800/53La, User Manual, Page: 101 / 314

Share
Download
NEC Express5800/53La User Manual Download Page 101

Configuring Your Workstation    4-29

RAID CONFIGURATION

This section describes the LSI Software RAID Configuration Utility. The LSI Software RAID
Configuration Utility resides in LSI Software RAID and is an OS-independent program.

Running LSI Software RAID Configuration Utility

On the POST screen after power-on, press 

Ctrl

 + 

M

 or 

Enter

 when the following message appears.

Press Ctrl-M or Enter to run LSI Software RAID Configuration Utility.

IMPORTANT: 

If you fail to press 

Ctrl

 + 

M

 or 

Enter

, or the system

proceeds without displaying the following screen, restart the system,
and press 

Ctrl

 + 

M

 on POST screen.

The LSI Software RAID Configuration Utility starts.

LSI Software RAID Configuration Utility TOP Menu

Summary of Contents for Express5800/53La



























































































































































































































































































































Reviews:

No comments