NEC Express5800/53La User Manual Download Page 58 | Manualshive

Page: 58 / 314

NEC Express5800/53La User Manual Download Page 58

3-2 Setting Up Your Workstation

SETUP FLOW

Follow the flowchart below to set up the workstation.

Installing optional devices

If you have purchased any optional device for the workstation, see Chapter 9 to install it.

Selecting the site

Select a suitable site for the workstation.

Connecting peripheral devices

Connect peripheral devices to the workstation.

Connecting the power cord

Connect the power cord to the workstation.

Turning on the workstation

Power on the workstation to start software setups. Setups depend on the optional
internal devices installed and the peripheral devices connected.

Installing the operating system

Install an operating system to the workstation. See Chapter 5.

Installing the utilities

Install the utilities in the provided NEC EXPRESSBUILDER DVD.
See Chapter 6.

Making backup copies of system information

After all the system setup procedures are completed, make backup copies of system
information.
System information is required for recovering the workstation from the trouble or after
replacing the system board.

«
...
56
57
58
59
60
...
»

Summary of Contents for Express5800/53La



























































































































































































































































































































Reviews:

No comments