NEC Express5800/53La User Manual Download Page 271

Page: 271 / 314

Installing Windows 7 D-13

10.

Select the type of installation you want.

[Custom (advanced)] is selected below.

11.

The screen of "Where do you want to install Windows?" is displayed.

NOTE:

Please go to step 14 when you do not use the RAID Controller,

and you have load the driver according to steps 6-8.

Remove the Backup DVD-ROM or Windows 7 Professional DVD-ROM and set NEC
EXPRESSBUILDER DVD, and select [Load Driver].

Load Driver

To install the device driver needed to access your hard
drive, insert the installation media containing the
driver files, and then click OK.

NOTE: The installation media can be a floppy disk, CD,
DVD, or USB flash drive.

[Browse] [OK] [Cancel]

Click [Browse], and go to Step 12.

Summary of Contents for Express5800/53La



























































































































































































































































































































Search results

Summary of Contents for Express5800/53La

Reviews:

NEC Express5800/53La, User Manual, Page: 271 / 314

Search results

Summary of Contents for Express5800/53La

Reviews: