manualshive.com logo in svg

NEC Express5800/53La, User Manual, Page: 193 / 314

Share
Download
NEC Express5800/53La User Manual Download Page 193

Maintenance  7-15

 

7. 

Follow the guide line shown at the bottom of the screen, and press the 

Esc 

key.

The [Enduser Menu] below is displayed.

Enduser Menu

Please choose a function by the arrow key and push Enter key.

<Test Result>

<Device List>
<Log Info>
<Option>
<Reboot>

TeDoLi (TEst & Diagnosis On Linux) Ver001.00 (Build020901.1.1m)

Enduser Menu

<Test Result>

Shows the diagnostics completion screen of the above diagnostics.

<Device List>

Shows a list of connected devices.

<Log Info

>

Shows the log information of the diagnostics. Log information can be
saved.
To save it, connect a FAT formatted removable media, and select
<Save(F)>.

<Option>

Optional features can be used from this menu.

<Reboot>

Reboots the system.

 

8. 

Select <Reboot> in the [Enduser Menu] above.

The workstation restarts and the system is started from the NEC EXPRESSBUILDER.

 

9. 

Exit the NEC EXPRESSBUILDER, and remove the DVD from the optical disk drive.

 

10. 

Power off the workstation and unplug the power cord from the receptacle.

 

11. 

Reconnect all the LAN cables that have been disconnected in Step 2 to the workstation.

 

12. 

Plug in the power cord.

This completes the system diagnostics.

Summary of Contents for Express5800/53La



























































































































































































































































































































Reviews:

No comments