manualshive.com logo in svg

Mitsubishi Electric MR-J2S-10CP, Instruction Manual

The Mitsubishi Electric MR-J2S-10CP is a high-performance servo amplifier, designed to provide precise control for industrial machines. To easily set up and operate this device, make sure to download the free Instruction Manual from manualshive.com, offering comprehensive details and guidelines for optimal performance and efficiency.

Share
Download
background image

 

 

15 -  29 

15. COMMUNICATION FUNCTIONS 

 

(c) Start of positioning operation 

Transmit the speed and acceleration/deceleration time constant, turn on the servo-on (SON) and 
forward/reverse rotation stroke end (LSP LSN), and then send the moving distance to start 
positioning operation. After that, positioning operation will start every time the moving distance is 
transmitted. To start opposite rotation, send the moving distance of a negative value. 
When the servo-on (SON) and forward/reverse rotation stroke end (LSP LSN)  are off, the 
transmission of the moving distance is invalid. Therefore, positioning operation will not start if the 
servo-on (SON) and forward/reverse rotation stroke end (LSP LSN) are turned on after the setting 
of the moving distance. 

 

(d) Temporary stop 

A temporary stop can be made during positioning operation. 

Command Data 

No. 

Data 

[A][0] [1][5] 

1EA5 

 

Retransmit the same communication commands as at the start time to resume operation. 
To stop positioning operation after a temporary stop, retransmit the temporary stop 
communication command. The remaining moving distance is then cleared. 

  

Summary of Contents for MR-J2S-10CP






































































































































































































































































































































































Reviews:

No comments

Related manuals for MR-J2S-10CP

Panasonic MINAS-BL GP series Technical Instructions preview
MINAS-BL GP series
Brand: Panasonic Pages: 9
Pangea Audio HP-101 User Manual preview
HP-101
Brand: Pangea Audio Pages: 7
Aaron ZA-100 Schematic Diagram preview
ZA-100
Brand: Aaron Pages: 2
DAPAudio VPA-060 Product Manual preview
VPA-060
Brand: DAPAudio Pages: 13
DAPAudio PA240 Owner'S Manual preview
PA240
Brand: DAPAudio Pages: 18
DAPAudio DSA-250 User Manual preview
DSA-250
Brand: DAPAudio Pages: 18
DAPAudio Palladium P-400 User Manual preview
Palladium P-400
Brand: DAPAudio Pages: 18
DAPAudio CA-4150 Manual preview
CA-4150
Brand: DAPAudio Pages: 16
Vanguard Dynamics VAIL CAST Quick Start Manual preview
VAIL CAST
Brand: Vanguard Dynamics Pages: 3
RAM BUX 2.8 Operation Manual preview
BUX 2.8
Brand: RAM Pages: 13
Arcam C31 Handbook preview
C31
Brand: Arcam Pages: 18
KODA KODA1000 Instruction Manual preview
KODA1000
Brand: KODA Pages: 35
Signal LCS652 Installation And Operating Instruction Manual preview
LCS652
Brand: Signal Pages: 16
Sansui AU-6500 Operating Instructions & Service Manual preview
AU-6500
Brand: Sansui Pages: 30
E&I 210L Manual preview
210L
Brand: E&I Pages: 9
D.W. Fearn VT-12 Operating Instructions Manual preview
VT-12
Brand: D.W. Fearn Pages: 37
Marantz PM7001KI Service Manual preview
PM7001KI
Brand: Marantz Pages: 46
Qtx QS12A User Manual preview
QS12A
Brand: Qtx Pages: 3

Brands by name

Popular brands

Load more brands