Mitel 6873i User Manual Download

Page: 212 / 259

Mitel 6873i SIP Phone Release 4.2.0 SP2 User Guide

210

Call Forward in Phone Mode

Press the configured

Call Fwd

softkey or press

and then the

Call Forward

icon.

The Call Forward screen displays and is applicable to all accounts configured on the phone.

Enter forwarding numbers using the dialpad keys or on-screen keyboard for any of the
following states:

•

All: Forwards all incoming calls for the respective account to the specified number.

•

Busy: Forwards incoming calls to a specified number if DND has been enabled for that
account OR if the account is currently engaged in another call.

•

No Answer: Forwards incoming calls to a specified number if the call has not been
answered for the specified number of rings.

If configuring a forwarding number for the No Answer state, press the

No. Rings

field and

press the left or right arrow button to change the desired number of rings.

Press the

checkbox beside the respective Call Forward mode to enable the Call Forward

mode.

Press the

Save

softkey to save your changes.

IP PHONE UI

Notes:

If All and Busy and No Answer are all enabled (and/or if the account has DND

enabled), the All settings take precedence over Busy and No Answer.

Pressing the

CopyToAll

key copies the call forward number of the Call Forward

mode in focus to every Call Forward mode of that account. For example, if you
have the cursor pointing at the All state and has a call forward phone number
configured, pressing the

CopytoAll

key assigns the same phone number to the

Busy and No Answer states as well.

Note:

Phone

mode, the configuration applies to all the accounts on the phone.

Summary of Contents for 6873i




































































































































































































































































Search results

Summary of Contents for 6873i

Reviews:

Related manuals for 6873i

Brands by name

Popular brands

Mitel 6873i, User Manual

Search results

Summary of Contents for 6873i

Reviews:

Related manuals for 6873i

Brands by name

Popular brands