Mitel 6873i User Manual Download | Manualshive

Page: 208 / 259

background image

Mitel 6873i SIP Phone Release 4.2.0 SP2 User Guide

206

CONFIGURING A CALL FORWARD KEY

The following describes the process of configuring Call Forward on your phone. To configure
a Call Forward key, see

“Call Forward Key”

on

page 124

.

CONFIGURING CALL FORWARD USING THE MITEL WEB UI

1.

Click on

Basic Settings > Preferences > General

.

2.

In the

Call Forward Key Mode

field, select a call forward mode to use on the phone.

•

Account (default): The Account mode allows you to configure Call Forward on a per

account basis. Pressing a configured

Call Forward

key applies to the account in focus.

•

Phone: The Phone mode allows you to set the same Call Forward configuration for all
accounts (All, Busy, and/or No Answer). When you configure the initial account, the
phone applies the configuration to all other accounts. (In the Mitel Web UI, only the
account you configured is enabled. All other accounts are greyed out but set to the
same configuration.) Using the Mitel Web UI, if you make changes to that initial account,
the changes apply to all accounts on the phone.

•

Custom: The Custom mode allows you to configure Call Forward for a specific account
or all accounts. You can configure a specific state (All, Busy, and/or No Answer) for
each account independently or all accounts. On the 6873i, you can set all accounts to

All On

,

All Off

, or copy the configuration for the account in focus to all other accounts

using a

CopytoAll

softkey.

MITEL WEB UI

Note:

If there is only one account configured on the phone, then the mode setting

is ignored and the phone behaves as if the mode was set to Phone.

«
...
206
207
208
209
210
...
»

Summary of Contents for 6873i




































































































































































































































































Reviews:

No comments

Related manuals for 6873i

Brand: Unitech Pages: 81

Brand: Yota Pages: 104

Brand: Acer Pages: 56

Brand: X-View Pages: 42

Brand: TCM Mobile Pages: 37

Brand: Samung Pages: 150

Brand: H3C Pages: 12

Brand: Blackberry Pages: 30

Brand: Tadiran Telecom Pages: 11

Brand: Sagem Pages: 97

OPENTOUCH ALE-300

Brand: Alcatel-Lucent Pages: 101

Brand: GAI-Tronics Pages: 92

Brand: Samsung Pages: 166

Brand: Samsung Pages: 224

Brand: Samsung Pages: 156

Brand: iPRIMUS Pages: 2

Brand: Splicecom Pages: 66

Brand: Adp Pages: 40

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands