Lenze i950 Series, Manual

Page: 466 / 500

Address Designation Default setting Data type Factor A M
0x243C:001 Device: Ethernet commands: Device: Start firmware
update Off/Ready [0] U8 CX
0x2450 Engineering port control No action/No error [0] U8 X
0x2451:001 Engineering port settings: IP address 0.0.0.0 U32 E
0x2451:002 Engineering port settings: Subnet 0.0.0.0 U32 E
0x2451:003 Engineering port settings: Gateway 0.0.0.0 U32 E
0x2451:004 Engineering port settings: DHCP Enabled [1] U8 -
0x2452:001 Active engineering port settings: IP address - (Read only) U32 EX
0x2452:002 Active engineering port settings: Subnet - (Read only) U32 EX
0x2452:003 Active engineering port settings: Gateway - (Read only) U32 EX
0x2452:005 Active engineering port settings: MAC address - (Read only) OCTET[6] X
0x245A:001 NTP server addresses: Activate NTP server
addresses No action/no error [0] U8 X
0x245A:002 NTP server addresses: NTP server address 1 0.0.0.0 U32 E
0x245A:003 NTP server addresses: NTP server address 2 0.0.0.0 U32 E
0x245A:004 NTP server addresses: NTP server address 3 0.0.0.0 U32 E
0x245A:005 NTP server addresses: NTP server address 4 0.0.0.0 U32 E
0x245B:001 System time: Time base NTP [0] U8 X
0x245B:002 System time: Current time ns U64 1 TX
0x2500 Touch probe filter time 0 us U16 1 -
0x2539:001 Hardware-Diagnose: 24 V supply actual voltage x.x V (Read only) U16 10 X
0x2539:002 Hardware-Diagnose: Control board temperature x.x °C (Read only) I16 10 X
0x2540:001 Mains settings: Rated mains voltage 400 Veff [1] U8 -
0x2540:002 Mains settings: Undervoltage warning threshold 430 V U16 1 -
0x2540:003 Mains settings: Undervoltage error threshold x V (Read only) U16 1 -
0x2540:004 Mains settings: Undervoltage reset threshold x V (Read only) U16 1 -
0x2540:005 Mains settings: Overvoltage warning threshold 795 V U16 1 -
0x2540:006 Mains settings: Overvoltage error threshold x V (Read only) U16 1 -
0x2540:007 Mains settings: Overvoltage reset threshold x V (Read only) U16 1 -
0x2540:008 Mains settings: DC link voltage critical - (Read only) U8 1 X ●
0x2541:003 Brake energy management: Reduced threshold 0 V U16 1 -
0x2550:001 Brake resistor: Minimum resistance x.x Ω (Read only) U16 10 X
0x2550:002 Brake resistor: Resistance value 180.0 Ω U16 10 -
0x2550:003 Brake resistor: Rated power 5600 W U32 1 -
0x2550:004 Brake resistor: Maximum thermal load 485 kWs U32 1 -
0x2550:006 Brake resistor: Reference resistance Minimum resistance [0] U8 -
0x2550:007 Brake resistor: Thermal load x.x % (Read only) U16 10 X
0x2550:008 Brake resistor: Warning threshold 90.0 % U16 10 -
0x2550:010 Brake resistor: Response to warning Warning [2] U8 -
0x2550:011 Brake resistor: Response to error No response [0] U8 -
0x2580:001 Distributed Clocks : Real time status - (Read only) U8 X
0x2580:002 Distributed Clocks : First setting time x ns (Read only) U64 1 TX
0x2580:003 Distributed Clocks : Newest setting time x ns (Read only) U64 1 TX
0x2580:004 Distributed Clocks : Current time x ns (Read only) U64 1 TX
0x2590:003 Energy saving: State of actual energy saving mode - (Read only) U8 HX
0x261C:001 Favorites settings: Parameter 1 U32 1 -
0x261C:002 Favorites settings: Parameter 2 U32 1 -
0x261C:003 Favorites settings: Parameter 3 U32 1 -
0x261C:004 Favorites settings: Parameter 4 U32 1 -
0x261C:005 Favorites settings: Parameter 5 U32 1 -
0x261C:006 Favorites settings: Parameter 6 U32 1 -
0x261C:007 Favorites settings: Parameter 7 U32 1 -
0x261C:008 Favorites settings: Parameter 8 U32 1 -
0x261C:009 Favorites settings: Parameter 9 U32 1 -
* Default setting depending on the size.
Appendix
Parameter attribute list
466