J&J Amusements 24v 1750 rpm Service Manual Download Page 57

Page: 57 / 171

Specifi cations and prices subject to change without notice. Download latest update to this manual on-line.

1-24

REMOVAL/INSTALLATION

Disconnect wiring from the boat hull to the boat top

(see wiring diagram on page 4-18).

Close the boat top.

From the rear, drill out the six rivets from the hull.

Remove the top from the hull.

Place the top upright on a soft surface.

REINFORCED RUBBER HINGE (Electric only)

EXCLUSIVE DESIGN & MANUFACTURED BY AUTOMATED BATTING CAGES

These batting cage balls are speci

cally designed for accuracy in ABC’s "wheel-style" pitching

machines. Along with the "standard" Urethane® balls, we also carry the "Soft

ight"; this

ball helps to reduce "bat sting" and pitches just like standard balls..right on track!

BATTING CAGE BALLS

Part#

Description Price

5-60-0001

Sup/ 890 Baseball, Yellow Urethane ® (DZ)

$43.00

5-60-0002

Sup/ 892 Baseball, Orange Soft

ight ® (DZ)

$45.00

5-60-0003

Sup/ 891 Softball, Yellow Urethane ® (DZ)

$52.46

Summary of Contents for 24v 1750 rpm












































































































































































Search results

Summary of Contents for 24v 1750 rpm

Reviews:

Related manuals for 24v 1750 rpm

Brands by name

Popular brands

J&J Amusements 24v 1750 rpm, Service Manual

Search results

Summary of Contents for 24v 1750 rpm

Reviews:

Related manuals for 24v 1750 rpm

Brands by name

Popular brands