J&J Amusements 24v 1750 rpm Service Manual Download Page 117

Page: 117 / 171

Specifi cations and prices subject to change without notice. Download latest update to this manual on-line.

3-30

Place the motor upside down with the motor cover removed.

Remove the six allen-cap screws.

Next, remove the four 5/16” nuts.

Note the placement and use of the

at washers

and spacer sleeves.

Make sure that all threads are treated with anti-

galling and corrosion resistant thread compound,

such as Loctite® Marine Grade Anti-Seize.

Remove the pivot shield.

Remove the pivot bracket.

NOTICE:

The UHMW plastic split insert has index

tabs; this is done so it remains static, and the pivot

turns, plastic-on-plastic, during operation.

Remove the pivot and insert bushings.

PIVOT

Index tabs

Insert bushing

Index tabs

Ins

ert bushing

CORROSION PROTECTION

Part#

Description Price

3-60-0002

Corrosion Block, Grease 2 oz. Tube

$6.25

99101

Corrosion Block, Aerosol 12 oz. Protector/Penetrant

$20.35

99101S

Corrosion Block, Pump Spray 4 oz. Protector/Penetrant

$8.15

99108

Corrosion Block, Grease 14oz Cartridge

$18.99

99109

Corrosion Block, Grease 16oz

$22.00

2-70-0112

Grease, Dielectric 5.3oz Tube Electrical Inulating & Protect

$23.80

Summary of Contents for 24v 1750 rpm












































































































































































Search results

Summary of Contents for 24v 1750 rpm

Reviews:

Related manuals for 24v 1750 rpm

Brands by name

Popular brands

J&J Amusements 24v 1750 rpm, Service Manual

Search results

Summary of Contents for 24v 1750 rpm

Reviews:

Related manuals for 24v 1750 rpm

Brands by name

Popular brands