J&J Amusements 24v 1750 rpm Service Manual Download Page 25

Page: 25 / 171

IC
A

IO
N

Specifi cations and prices subject to change without notice. Download latest update to this manual on-line.

BOAT ASSEMBLY

Lift the hull assembly and carefully place it inside the tube.

‹ CAUTION ›

e hull is heavy. Use two

people when lift ing the hull assembly.

Make sure to grab the lip of the boat bottom when lift ing the assembly.

USE WORK GLOVES TO PROTECT HANDS

FROM FIBERGLASS EDGES.

Rotate the boat hull inside of the tube so the air valve on the tube

is located at the back of the hull. Th

is allows simple maintenance

to be performed from one direction on the bumper boat, as well

as reducing the risks posed by guests accessing the valve.

is adapter makes it easy to fi ll your supertube and check pressure.

J&J # 2-60-A0006

SUPERTUBE PRESSURE TEST
ADAPTER AND FILLER

Summary of Contents for 24v 1750 rpm












































































































































































Search results

Summary of Contents for 24v 1750 rpm

Reviews:

Related manuals for 24v 1750 rpm

Brands by name

Popular brands

J&J Amusements 24v 1750 rpm, Service Manual

Search results

Summary of Contents for 24v 1750 rpm

Reviews:

Related manuals for 24v 1750 rpm

Brands by name

Popular brands