J&J Amusements 24v 1750 rpm Service Manual Download Page 40

Page: 40 / 171

phone: 1-800-854-3140 | 1-503-304-8899 fax: 1-800-366-7505 | 1-503-304-1899 www.jjamusements.com

1-7

Removal/Installation

The bilge pump fuse is located on the back of

the boat top to the left of the vent plate.

With a

at screwdriver, push and turn

counterclockwise 1/4 turn.

Remove the fuse and holder by pulling outward.

Remove the fuse from the holder.

Check for continuity through the fuse with a multimeter

(see page 4-6 for a fuse test).

NOTE:

The replaceable fuse is a 3-amp time-delay/

slow-blow cartridge-style fuse. Using any fuse

type other than this speci

cation could result in

poor performance and/or pump failure.

Replace as needed.

BILGE PUMP FUSE (Electric only)

FUSE & FUSE RELATED

Part#

Description

Price

2-70-0104

Fuse, 3 Amp Slow Blow (Squirter & 24v Bilge Pump)

$1.53

Summary of Contents for 24v 1750 rpm












































































































































































Search results

Summary of Contents for 24v 1750 rpm

Reviews:

Related manuals for 24v 1750 rpm

Brands by name

Popular brands

J&J Amusements 24v 1750 rpm, Service Manual

Search results

Summary of Contents for 24v 1750 rpm

Reviews:

Related manuals for 24v 1750 rpm

Brands by name

Popular brands