J&J Amusements 24v 1750 rpm Service Manual Download Page 30

Page: 30 / 171

phone: 1-800-854-3140 | 1-503-304-8899 fax: 1-800-366-7505 | 1-503-304-1899 www.jjamusements.com

BOAT LAUNCH PROCEDURE

Latch the dock ropes to the dock rails and the boat to secure the boat to

the dock rails. Th

ere should be two ropes and two dock rails per boat.

Install the boat & dock rail hooks as described in

the dock rope installation on page 1-12.

Carefully move the boat to the edge of the pond.

NOTICE

Make sure to move the boat with the box lid

underneath it to prevent damage.

‹ CAUTION ›

is is a two-person job. Do not try to

launch a bumper boat with only one person.

Carefully slide the boat assembly (without the motor) into the pond.

Inspect the boat and latch the boat hooks to the dock rails.

CHECK TUBE PRESSURE EASILY & ACCURATELY
WITH THE LOW-PRESSURE GAUGE #3-96-0024

Summary of Contents for 24v 1750 rpm












































































































































































Search results

Summary of Contents for 24v 1750 rpm

Reviews:

Related manuals for 24v 1750 rpm

Brands by name

Popular brands

J&J Amusements 24v 1750 rpm, Service Manual

Search results

Summary of Contents for 24v 1750 rpm

Reviews:

Related manuals for 24v 1750 rpm

Brands by name

Popular brands