J&J Amusements 24v 1750 rpm Service Manual Download Page 107

Page: 107 / 171

Specifi cations and prices subject to change without notice. Download latest update to this manual on-line.

3-20

Remove the motor cover and neoprene protector

(see page 3-3).

Remove the magnetic trigger by removing the

1/4” shoulder bolt with an allen wrench.

Inspect the nylon bushing and shoulder bolt.

Replace as needed.

Align the rode with the slot in the handlebars.

Make sure the magnet in the trigger is pointed

down, facing the solid state switch.

Tighten the shoulder bolt.

NOTICE:

Mounting the magnet upside down will

result in a poor or nonfunctional sold state switch.

Tighten the shoulder bolt.

MAGNETIC TRIGGER

tto

Summary of Contents for 24v 1750 rpm












































































































































































Search results

Summary of Contents for 24v 1750 rpm

Reviews:

Related manuals for 24v 1750 rpm

Brands by name

Popular brands

J&J Amusements 24v 1750 rpm, Service Manual

Search results

Summary of Contents for 24v 1750 rpm

Reviews:

Related manuals for 24v 1750 rpm

Brands by name

Popular brands