J&J Amusements 24v 1750 rpm Service Manual Download Page 72

Page: 72 / 171

phone: 1-800-854-3140 | 1-503-304-8899 fax: 1-800-366-7505 | 1-503-304-1899 www.jjamusements.com

2-5

Unscrew the clamps and remove the protector.

Carefully remove and clean any

silicone from the boat hull.

Install the protector and tighten the clamps securely.

Apply silicone between the boat hull and protector.

(For best results, use J&J #013331.)

Let the silicone cure before putting

the boat back in service.

Note:

Curing time varies depending on outside

temperature and amount of silicone used

(see silicone instructions for details).

BOAT HALF PROTECTOR (Electric only)

MARINE GOOP ADHESIVE #013331; the PERFECT SOLUTION

TO ATTACH BOAT HALF PROTECTOR.

Silicone

THREAD LOCKERS & GLUES

Part#

Description Price

013330

Glue, 3.7oz Tube (Goop)

$10.81

013331

Glue, Goop Cartridge

$11.22

Marine Goop

Summary of Contents for 24v 1750 rpm












































































































































































Search results

Summary of Contents for 24v 1750 rpm

Reviews:

J&J Amusements 24v 1750 rpm, Service Manual, Page: 72 / 171

Search results

Summary of Contents for 24v 1750 rpm

Reviews: