J&J Amusements 24v 1750 rpm Service Manual Download Page 119

Page: 119 / 171

Specifi cations and prices subject to change without notice. Download latest update to this manual on-line.

3-32

Install the drive shaft housing bushings.

Install the pivot and bushings.

Install the pivot shield.

Install and tighten the pivot bracket nuts to 20 ft. lbs.

<WARNING>

If the pivot bracket nuts are over-tightened,

binding of the pivot assembly may occur.

Finish by installing the allen-cap-headed screws.

Make sure to have the

ex wire cable

clamps in the correct position

(see

ex wire removal on page 3-8).

Mechanix Wear

kevlar knee pads

Mechanix Wear

original glove

Mechanix Wear

mechanics apron

Mechanix Wear

radio belt

PROTECTIVE CLOTHING/GEAR

Part#

Description Price

3-00-5000

Glove, Original 8 Small Mechanix Black

$37.01

3-00-5001

Glove, Original 9 Medium Mechanix Black

$37.01

3-00-5002

Glove, Original 10 Large Mechanix Black

$37.01

3-00-5003

Glove, Original 11 X-Large Mechanix Black

$37.01

3-00-5010

Belt, Support Mechanix Black Fits 30” to 40” Waist

$59.16

3-00-5011

Belt, Mechanix Black/White Fits 28” to 42” Waist

$23.62

3-00-5008

Apron, Mechanix Black

$36.94

3-00-5009

Knee-Pad, Mechanix Black

$75.46

Mechanix Wear

support Belt

Summary of Contents for 24v 1750 rpm












































































































































































Search results

Summary of Contents for 24v 1750 rpm

Reviews:

Related manuals for 24v 1750 rpm

Brands by name

Popular brands

J&J Amusements 24v 1750 rpm, Service Manual

Search results

Summary of Contents for 24v 1750 rpm

Reviews:

Related manuals for 24v 1750 rpm

Brands by name

Popular brands