J&J Amusements 24v 1750 rpm Service Manual Download Page 85

Page: 85 / 171

Specifi cations and prices subject to change without notice. Download latest update to this manual on-line.

2-18

Tool, supertube valve tightener (plastic style)

part # 2-60-0123

Place the patch over the damaged tube surface

and use roller or old spoon to squeeze any air

out of the patch, pressing the material together.

Wait at least 24 to 48 hours before

rein

ating the tube.

Pressure test the tube by in

ating it and

checking the patch with soapy water.

If desired, leave the tube in

ated overnight and

recheck it before putting it back into service.

NOTE:

When patching, the relative humidity must

be less than 70%, preferably as low as 40%.

Temperature should be 64°C to 77°C ( 147.2°F.

to 170.6°F.). Bond strength drops very rapidly

with heat or high humidity. Don’t patch the

tube near water or in direct sunlight.

TUBE TOOLS - BUMPER BOAT

Part#

Description

Price

2-60-0046

Gauge, Low Pressure 0-15 (Used for Super Tube)

$58.00

3-96-0024

Gauge, Low Pressure 0-15 (Super Tube & Poly Tube(Motion Pro)

$95.00

2-60-0123

Tool, Super Tube Valve Tightener (Plastic Style)

$5.56

#3-96-0024

Low pressure gauge (reads

up to 15psi)

#2-60-0046

Summary of Contents for 24v 1750 rpm












































































































































































Search results

Summary of Contents for 24v 1750 rpm

Reviews:

Related manuals for 24v 1750 rpm

Brands by name

Popular brands

J&J Amusements 24v 1750 rpm, Service Manual

Search results

Summary of Contents for 24v 1750 rpm

Reviews:

Related manuals for 24v 1750 rpm

Brands by name

Popular brands