J&J Amusements 24v 1750 rpm Service Manual Download Page 63

Page: 63 / 171

Specifi cations and prices subject to change without notice. Download latest update to this manual on-line.

1-30

The battery

lling system allows easy top-o

ﬀ

of the battery

water level from the outside of the boat. Simply attach the

battery

ll squeeze bulb (J&J#2-70-A0021C) to the access port

on the back of the boat top to

ll all the batteries to equal

levels.

Hold the quick-release coupler from outside so it

doesn’t spin while loosening the inside nut.

Loosen the hose clamp.

Remove the hose from the coupler.

Loosen and remove the plastic nut.

Remove the coupler from the outside of the boat top.

(J&J #2-70-0108)

BATTERY-FILL QUICK-RELEASE COUPLER

STRAIN RELIEF

2-70-0211

This combination strain relief and plug end protector has an easy

to grab hand hold for connecting and disconnecting SB-120 charger

plugs from your bumper boats. No more broken plug ends from

charger leads being dropped on the ground.

BATTERY PLUG ENDS

Part#

Description

Price

2-70-A0018

Plug Adapter, SB50 to SB120 Adaptor for Master Charger

$35.85

2-70-A0022

Plug Assy., SB-120 Complete w/Housing, Strain Relief,Term

$21.99

2-70-0097

Terminal Contact, SB-120 Nickel Plated (each)

$6.99

2-70-0211

Cover, SB120 FPX (each half)

$5.61

2-70-0211KIT

Cover, SB120 FPX Kit (includes hardware and two halves)

$14.03

#2-70-A0022

Summary of Contents for 24v 1750 rpm












































































































































































Search results

Summary of Contents for 24v 1750 rpm

Reviews:

Related manuals for 24v 1750 rpm

Brands by name

Popular brands

J&J Amusements 24v 1750 rpm, Service Manual

Search results

Summary of Contents for 24v 1750 rpm

Reviews:

Related manuals for 24v 1750 rpm

Brands by name

Popular brands