J&J Amusements 24v 1750 rpm Service Manual Download Page 44

Page: 44 / 171

phone: 1-800-854-3140 | 1-503-304-8899 fax: 1-800-366-7505 | 1-503-304-1899 www.jjamusements.com

1-11

The safety rails are mounted with 6 phillips

head bolts, 6 nylock nuts and

at washers.

REMOVAL/INSTALLATION

Hold each screw from the outside of the boat top.

Remove the nylock nuts and

at washers.

Replace the hardware as needed.

Each dock rail hook is mounted with 1 U-bolt, 1 outside plate,

1 inside plate, 4 nylock nuts and 4 lock washers.

REMOVAL/INSTALLATION

Remove the nylock nuts and the inside plate.

Replace the hardware as needed.

SAFETY RAILS & DOCK RAIL HOOKS

BOAT HOOKS & ROPE

Each boat should have two Boat Hooks and 3 to 5 feet of

bumper boat rope. (Note: Bumper boat rope is determined

by how far dockrails are spaced from edge of pool.)

ROPE - BUMPER BOAT

Part#

Description Price

00388

Rope, Yellow Bumper Boat (Sold By Ft)

$0.51

00036-S

Hook, Snap Style Boat (Standard)

$8.99

00387

Fid, Rope Splicing 1/2”

$2.24

Summary of Contents for 24v 1750 rpm












































































































































































Search results

Summary of Contents for 24v 1750 rpm

Reviews:

Related manuals for 24v 1750 rpm

Brands by name

Popular brands

J&J Amusements 24v 1750 rpm, Service Manual

Search results

Summary of Contents for 24v 1750 rpm

Reviews:

Related manuals for 24v 1750 rpm

Brands by name

Popular brands