KL Industries Bass Hound 10.2 Owner'S Manual Download

Page: 1 / 10

FISHING BOAT

OWNER’S MANUAL

Bass Hound™ 9.4

Bass Hound™ 10.2

KL Industries, Inc.

1790 Sun Dolphin Dr.

Muskegon, MI 49444

Phone 231-733-2725

Fax 231-739-4502

Email [email protected]

Website www.klindustries.com

March 2007

Bass Hound™

9.4

Bass Hound™

10.2

THANK YOU

Thank you for purchasing this fishing boat from

KL Industries, Inc.

Congratulations on the recent purchase of your new fishing

boat. You have purchased a boat from one of the nations

leading manufacturers of small boats. Your boat represents

years of commitment to product design, excellence in

engineering and quality in manufacturing. With proper care

and maintenance your pedal boat should last for many

years to come. Please call our helpful and knowledgeable

Customer Support Department if you have any questions.

KL Industries, Inc.

1790 Sun Dolphin Dr.

Muskegon, MI 49444

Phone 231-733-2725

Fax 231-739-4502

Email [email protected]

Website www.klindustries.com

Summary of Contents for Bass Hound 10.2











Search results

Summary of Contents for Bass Hound 10.2

Reviews:

Related manuals for Bass Hound 10.2

Brands by name

Popular brands

KL Industries Bass Hound 10.2, Owner'S Manual

Search results

Summary of Contents for Bass Hound 10.2

Reviews:

Related manuals for Bass Hound 10.2

Brands by name

Popular brands