J&J Amusements 24v 1750 rpm Service Manual Download Page 131

Page: 131 / 171

Specifi cations and prices subject to change without notice. Download latest update to this manual on-line.

3-44

SB-120 TERMINAL REPLACEMENT

Install a clear tube (J&J #2-60-0094) over the cable

and install strain relief on both sides of the cable

utilizing the two pan head-screws and nylocks.

Insert the terminal contacts into the SB-120 housing

and push until the terminal snaps into the housing.

NOTICE:

THE WHITE WIRE IS TO POSITIVE, THE BLACK

WIRE IS NEGATIVE. REVERSING THESE LEADS WILL

RESULT IN A BLOWN CHARGER OUTPUT FUSE.

Install and tighten strain relief to the housing

using the machine screw and nylock.

THE RIGHT TOOL FOR THE JOB.
CRIMP WITH EASE! J&J #2-70-0073-120

BATTERY ACCESSORIES

Part#

Description

Price

2-70-0073-120

Tool, Terminal Crimper Hex Crimp Jr. (SB-50 & SB-120)

$235.99

Summary of Contents for 24v 1750 rpm












































































































































































Search results

Summary of Contents for 24v 1750 rpm

Reviews:

Related manuals for 24v 1750 rpm

Brands by name

Popular brands

J&J Amusements 24v 1750 rpm, Service Manual

Search results

Summary of Contents for 24v 1750 rpm

Reviews:

Related manuals for 24v 1750 rpm

Brands by name

Popular brands