J&J Amusements 24v 1750 rpm Service Manual Download Page 113

Page: 113 / 171

Specifi cations and prices subject to change without notice. Download latest update to this manual on-line.

3-26

Remove the magnetic trigger

(see page 3-19).

Remove the wire leads from the power post

(see wiring diagram on page 4-19).

On the under-side of the motor, remove the

solid state switch mounting nuts.

SOLID STATE SWITCH

Remove the solid state switch.

Note:

There is NO left or right solid state switch; it can be

installed on the squirt (blue rod) or motor (green rod) side.

The LED light on the switch must face

the inside of the control rods

(solid state switch part # 2-30-A0002).

Summary of Contents for 24v 1750 rpm












































































































































































Search results

Summary of Contents for 24v 1750 rpm

Reviews:

Related manuals for 24v 1750 rpm

Brands by name

Popular brands

J&J Amusements 24v 1750 rpm, Service Manual

Search results

Summary of Contents for 24v 1750 rpm

Reviews:

Related manuals for 24v 1750 rpm

Brands by name

Popular brands