manualshive.com logo in svg

J&J Amusements 24v 1750 rpm, Service Manual, Page: 26 / 171

Share
Download
J&J Amusements 24v 1750 rpm Service Manual Download Page 26

27

SP

E

C

IF

IC

A

T

IO

N

S

phone: 1-800-854-3140 | 1-503-304-8899   fax: 1-800-366-7505 | 1-503-304-1899   www.jjamusements.com

 BATTERY INSTALLATION (Electric only)

Open the boat top and use the wooden prop rod to hold the top up.

‹ CAUTION › 

Place the wooden prop rod so it does not become 

dislodged while holding the boat top in “up” position.

• 

Remove items provided inside boat:

• 

Wooden prop rod (qty 1)

• 

Battery cables (qty 3) 

• 

Battery fi ll kit (qty 1) 

• 

Wiring schematic (qty 1) 

• 

Battery fi ll kit instructions 

Batteries should be placed in such a position as to allow ease of wiring. 

Place the batteries with terminals as shown in Figure 1. Place battery 

#1 in the hull fi rst, followed by battery #4, #2, and fi nally, #3. Th

 is 

sequence helps keep the boat balanced during battery installation.

Fig. 1

+

Battery 2

Battery 4

-

-

-

-

+

+

+

‹ CAUTION › 

Proper lift ing procedures must be followed.

Carefully place batteries in the battery trays 

located inside the bottom hull.

NOTICE

  J&J recommends using a battery carrier

(J&J #2-60-0034) when installing/moving heavy batteries.

Battery 1

Battery 3

SAFELY REMOVE, LIFT, AND adjust HEAVY BATTERIES 
WITH THIS BATTERY CARRIER, j&j # 2-60-0034

Summary of Contents for 24v 1750 rpm












































































































































































Reviews:

No comments