J&J Amusements 24v 1750 rpm Service Manual Download Page 87

Page: 87 / 171

Specifi cations and prices subject to change without notice. Download latest update to this manual on-line.

2-20

Fill the tube using the Super Tube

adapter and an air-

ller nozzle.

ate the tube to the recommended PSI of 3 lbs.

Before returning the boat to service, check the valve

for leaks by applying a solution of soapy water.

If bubbles form, the valve needs to be tightened.

With the tube in

ated, insert the valve

tightener and turn the nut 1/8th turn.

Re-check with soapy water solution. Repeat

as needed until no bubbles form.

#2-60-0124

TUBE TOOLS - BUMPER BOAT

Part#

Description

Price

2-60-0124

Tool, In

ator/De

ator Super Tube 4.0hp 130cfm

$199.00

THE SUPER TUBE INFLATOR/DEFLATOR IS SIMPLY A GREAT TOOL. ITS 4HP MOTOR
GENERATES ENOUGH AIR MOVEMENT TO FILL A SUPER TUBE IN 30 SECONDS!

Its also great for blow drying your go karts after washing.

Summary of Contents for 24v 1750 rpm












































































































































































Search results

Summary of Contents for 24v 1750 rpm

Reviews:

Related manuals for 24v 1750 rpm

Brands by name

Popular brands

J&J Amusements 24v 1750 rpm, Service Manual

Search results

Summary of Contents for 24v 1750 rpm

Reviews:

Related manuals for 24v 1750 rpm

Brands by name

Popular brands