J&J Amusements 24v 1750 rpm Service Manual Download Page 102

Page: 102 / 171

phone: 1-800-854-3140 | 1-503-304-8899 fax: 1-800-366-7505 | 1-503-304-1899 www.jjamusements.com

3-15

Remove the four 3/8” hex-head motor mount bolts.

Remove the handle bar assembly

(see page 3-7).

Remove the drive shaft housing.

DO YOU NEED A CORROSION CONTROL SOLUTION?

CORROSION BLOCK SOLVES YOUR PROBLEMS!

Experts estimate that protecting your equipment now is ten times cheaper than repairing it later. As a bonus, electrical
and mechanical parts will run smoother and more e

ﬃ

ciently.

SO WHAT IS IT?

Corrosion Block is a revolutionary product that:



Kills corrosion on contact.



Stops corrosion from ever coming back.



Lubricates the area.



Is safe to nearly all electronics.

CORROSION PROTECTION

Part#

Description Price

3-60-0002

Corrosion Block, Grease 2 oz. Tube

$6.25

99101

Corrosion Block, Aerosol 12 oz. Protector/Penetrant

$20.35

99101S

Corrosion Block, Pump Spray 4 oz. Protector/Penetrant

$8.15

99108

Corrosion Block, Grease 14oz Cartridge

$18.99

99109

Corrosion Block, Grease 16oz

$22.00

2-70-0112

Grease, Dielectric 5.3oz Tube Electrical Inulating & Protect

$23.80

DID YOU KNOW THAT CORROSION BLOCK:



Is the US military’s corrosion control product of choice?



Was used during the

lming of The Titanic?



Was used during the

lming of Water World?

Summary of Contents for 24v 1750 rpm












































































































































































Search results

Summary of Contents for 24v 1750 rpm

Reviews:

Related manuals for 24v 1750 rpm

Brands by name

Popular brands

J&J Amusements 24v 1750 rpm, Service Manual

Search results

Summary of Contents for 24v 1750 rpm

Reviews:

Related manuals for 24v 1750 rpm

Brands by name

Popular brands