J&J Amusements 24v 1750 rpm Service Manual Download Page 23

Page: 23 / 171

IC
A

IO
N

Specifi cations and prices subject to change without notice. Download latest update to this manual on-line.

Cut and remove the metal packing straps.

Remove the box top and place it aside for later use. Remove the box

sides and discard. Remove the tube and place it aside with the box top.

Remove plastic wrap from the boat hull and discard. Leave the

boat hull on the cardboard base for protection from scratches.

UNPACKING

J&J carries many cleaning and
protection products to keep your
go-karts in top condition. From
smaller spray bottles to 5 gallon
containers of product, we’ve got
you covered. Give us a call!

CLEANERS AND PROTECTANTS

CLEANERS & PROTECTANTS

Part#

Description Price

00316

Cleaner, Protect All Cleaner

$19.26

00317

Cleaner, Protect All Wash

$14.81

00320

Cleaner, Protect All 13oz Aerosol Spray

$14.81

3-60-0033

Protectant, 303 Aerospace 2 oz. pump sprayer

$2.75

3-60-0034

Protectant, 303 Aerospace 32 oz. trigger sprayer

$24.43

3-60-0035

Protectant, 303 Aerospace 128 oz. gallon refi ll

$64.21

3-60-0037

Protectant, 303 Aerospace 5 gallon Bucket

$279.99

3-60-0078

Cleaner, Spray Cleaner/Polish

$9.99

Summary of Contents for 24v 1750 rpm












































































































































































Search results

Summary of Contents for 24v 1750 rpm

Reviews:

Related manuals for 24v 1750 rpm

Brands by name

Popular brands

J&J Amusements 24v 1750 rpm, Service Manual

Search results

Summary of Contents for 24v 1750 rpm

Reviews:

Related manuals for 24v 1750 rpm

Brands by name

Popular brands