J&J Amusements 24v 1750 rpm Service Manual Download Page 55

Page: 55 / 171

Specifi cations and prices subject to change without notice. Download latest update to this manual on-line.

1-22

The vent plate is located at the rear of the boat top.

Open the vent plate to access the charging

cable, and to perform visual inspections.

VENT PLATE ASSEMBLY (Electric only)

The vent plate assembly is mounted with six 10-32

phillips-head screws with six 10-32 nylock nuts.

To replace the vent plate assembly,

remove the six screws.

Inspect the gasket for damage

and replace as needed.

To open, turn counterclockwise.

Ven

t Pla

Protect your boat from harmful ULTRA VIOLET rays and keep it looking like new with 303

Aerospace Protectant!

CLEANERS & PROTECTANTS

Part#

Description Price

3-60-0033

Protectant, 303 Aerospace 2 oz. pump sprayer

$2.75

3-60-0034

NLA/Protectant, 303 Aerospace 32 oz. trigger sprayer

$24.43

3-60-0035

Protectant, 303 Aerospace 128 oz. gallon re

$64.21

3-60-0037

NLA/Protectant, 303 Aerospace 5 gallon Bucket

$279.99

3-60-0078

Cleaner, Spray Cleaner/Polish

$9.99

Summary of Contents for 24v 1750 rpm












































































































































































Search results

Summary of Contents for 24v 1750 rpm

Reviews:

J&J Amusements 24v 1750 rpm, Service Manual, Page: 55 / 171

Search results

Summary of Contents for 24v 1750 rpm

Reviews: