J&J Amusements 24v 1750 rpm Service Manual Download Page 121

Page: 121 / 171

Specifi cations and prices subject to change without notice. Download latest update to this manual on-line.

3-34

Remove the gearbox assembly.

Next, remove the gasket and discard, as this item

will be replaced with a new gasket. (J&J #01981).

Grasp the end of the shaft and remove.

NOTICE:

The keyway is welded in place on both

ends of the drive shaft. If the keyway is damaged

or worn, the drive shaft must be replaced.

The drive shaft can be installed in either direction.

Before installing the shaft, coat both ends with

MARINERS CHOICE NEVER SEEZ®.

GEARBOX AND DRIVE SHAFT

Lower the shaft into the housing. When the shaft contacts the

motor output shaft, rotate the shaft in order to align the

motor shaft slot and the drive shaft keyway; you will

feel the drive shaft move toward the motor when this

occurs.

Coat both sides of the new gasket with a thin coating of silicone

sealant and install on the housing.

Make sure to align the key slot on the gearbox shaft with

the keyway on the drive shaft.

Tighten the mounting bolts.

Summary of Contents for 24v 1750 rpm












































































































































































Search results

Summary of Contents for 24v 1750 rpm

Reviews:

Related manuals for 24v 1750 rpm

Brands by name

Popular brands

J&J Amusements 24v 1750 rpm, Service Manual

Search results

Summary of Contents for 24v 1750 rpm

Reviews:

Related manuals for 24v 1750 rpm

Brands by name

Popular brands