J&J Amusements 24v 1750 rpm Service Manual Download Page 58

Page: 58 / 171

phone: 1-800-854-3140 | 1-503-304-8899 fax: 1-800-366-7505 | 1-503-304-1899 www.jjamusements.com

1-25

Drill out the rivets and remove the rubber hinge.

Insert

ve 3/16”x 3/4” aluminum rivets (J&J#002473)

through the bracket and rubber hinge.

Install the rivets through the backing plate

of the rubber hinge and the boat top.

J&J carries all locktite brand threadlocker and other sealants.

THREAD LOCKERS & GLUES

Part#

Description Price

3-20-0002

Loctite, Threadlocker 50ml Bottle (Blue)

$83.73

3-20-0003

Loctite, Threadlocker 250ml Bottle (Blue)

$191.76

3-20-0005

Loctite, Threadlocker 50ml Bottle (Red)

$76.60

3-20-0006

Loctite, Threadlocker 250ml Bottle (Red)

$191.76

4-95-0044

Loctite, 50ML “Green”

$94.07

81790

Loctite, Blue 250 ml

$217.14

81793

Loctite, Red 250 ml

$232.74

Summary of Contents for 24v 1750 rpm












































































































































































Search results

Summary of Contents for 24v 1750 rpm

Reviews:

J&J Amusements 24v 1750 rpm, Service Manual, Page: 58 / 171

Search results

Summary of Contents for 24v 1750 rpm

Reviews: