J&J Amusements 24v 1750 rpm Service Manual Download Page 83

Page: 83 / 171

Specifi cations and prices subject to change without notice. Download latest update to this manual on-line.

2-16

Fully in

ate the tube.

Place three to four drops of washing

detergent in a spray bottle with water.

Check small areas of the tube at a time, spraying the

surface of the tube and looking for any bubbles.

Draw a small circle around any punctures

or rips in the tube (for easy location

of the repair), then de

ate tube.

NOTE:

The glue and patch will bubble up and

fail to bond properly if the tube is fully

ated when the repair is made.

Do not attempt to patch around or near a

tube seam, as the patch will not bond.

CHECKING SUPER TUBE FOR LEAKS

TUBE REPAIR - BUMPER BOAT

Part#

Description

Price

003370

Patch, Supertube Repair Kit

$50.38

003371

Patch, Supertube Maintenance & Repair Kit

$101.99

#003371, Super Tube

maintenance & repair kit

Summary of Contents for 24v 1750 rpm












































































































































































Search results

Summary of Contents for 24v 1750 rpm

Reviews:

J&J Amusements 24v 1750 rpm, Service Manual, Page: 83 / 171

Search results

Summary of Contents for 24v 1750 rpm

Reviews: