J&J Amusements 24v 1750 rpm Service Manual Download Page 130

Page: 130 / 171

phone: 1-800-854-3140 | 1-503-304-8899 fax: 1-800-366-7505 | 1-503-304-1899 www.jjamusements.com

3-43

Part # 2-70-A0022 includes:

Strain relief (2)

Terminal contacts (2)

6-32 nylock nut (1)

6-32 machine screw (1)

10-32 nylock nut (2)

10-32 x 3/4 pan head screw (2)

SB-120 housing (1)

NOTE: SB-120 ASSEMBLY DOES NOT CONTAIN

CLEAR POLY VINYL TUBING # 2-60-0094

Remove the cable shielding back 1-1/2”

Strip the wire shielding back 3/4”.

Insert the terminal contacts and crimp the terminal

to the wire using a hydraulic crimp tool, such as

Central Hydraulics from Harbor Freight.

Note: Attempting to to crimp new terminals with a

vise/hammer, etc. will result in a poor connection.

SB-120 TERMINAL REPLACEMENT

<<WARNING>>

You must

rst disconnect the

negative battery pack cable from the power

post.

DO NOT WORK ON CABLES THAT

ARE STILL CONNECTED TO POWER.

Terminals can be removed by pushing down on

the housing clips and pulling on the cable.

Cable s

hieldin

re S

hie

ldi

Summary of Contents for 24v 1750 rpm












































































































































































Search results

Summary of Contents for 24v 1750 rpm

Reviews:

Related manuals for 24v 1750 rpm

Brands by name

Popular brands

J&J Amusements 24v 1750 rpm, Service Manual

Search results

Summary of Contents for 24v 1750 rpm

Reviews:

Related manuals for 24v 1750 rpm

Brands by name

Popular brands