J&J Amusements 24v 1750 rpm Service Manual Download Page 162

Page: 162 / 171

phone: 1-800-854-3140 | 1-503-304-8899 fax: 1-800-366-7505 | 1-503-304-1899 www.jjamusements.com

6-3

BOAT TOP DECALS

J&J Amusements website decal is located at the

right rear of the boat top under the vent plate.

(J&J #009800)

“Blaster Boat” decal is located on

the boat top above the vent plate

on the electric bumper boat.

(J&J #001688)

“Water Bug” decal is located on

the boat top above the water drain

plug on the gas bumper boat.

(J&J #00168)

“Warning-Keep Hands And Feet

In Boat At All Times”

decal is located on the right

inboard side of the boat top.

(J&J #00169)

<SAFETY ITEM>

This decal must be readable at all

times to operate the boat.

Replace as needed.

Summary of Contents for 24v 1750 rpm












































































































































































Search results

Summary of Contents for 24v 1750 rpm

Reviews:

Related manuals for 24v 1750 rpm

Brands by name

Popular brands

J&J Amusements 24v 1750 rpm, Service Manual

Search results

Summary of Contents for 24v 1750 rpm

Reviews:

Related manuals for 24v 1750 rpm

Brands by name

Popular brands