J&J Amusements 24v 1750 rpm Service Manual Download Page 31

Page: 31 / 171

IC
A

IO
N

Specifi cations and prices subject to change without notice. Download latest update to this manual on-line.

Have a helper carefully pass the motor assembly to the

person in the boat.

GAS ENGINE

Check the engine and gear box oil level before installing.

“Refer to the Honda owner’s manual “

Position the lower unit of the motor so the prop guard will clear

the motor pivot. Carefully lower the motor through the hole. Align

the motor to the motor pivot and slide down into place. Th

ere is an

index hole and pin that need to be aligned for proper positioning.

NOTE:

For electric powered boats only.

Treat all SB120 plug terminals with corrosion block (J&J part #99109).

Connect the blue SB120 plug from the boat hull

into the blue SB120 plug on the motor.

NOTICE

Boats equipped with remote shut down (Boat Captain system) will

need the system to be activated from the transmitter before the boat

can operate.

Index p

oint

MOTOR INSTALLATION

CORROSION SOLUTION! CORROSION BLOCK PRODUCTS
AVAILABLE AT J&J.

Summary of Contents for 24v 1750 rpm












































































































































































Search results

Summary of Contents for 24v 1750 rpm

Reviews:

Related manuals for 24v 1750 rpm

Brands by name

Popular brands

J&J Amusements 24v 1750 rpm, Service Manual

Search results

Summary of Contents for 24v 1750 rpm

Reviews:

Related manuals for 24v 1750 rpm

Brands by name

Popular brands