J&J Amusements 24v 1750 rpm Service Manual Download Page 103

Page: 103 / 171

Specifi cations and prices subject to change without notice. Download latest update to this manual on-line.

3-16

Before motor disassembly, make sure to mark the

location of the cap in relation to the motor casing.

NOTICE

If the motor cap is assembled 180 degrees o

ﬀ

this will reverse polarity and cause the

motor to turn counterclockwise.

Remove the fan cover.

Remove the fan bolt and slide the fan o

ﬀ

of the shaft.

Supertube

ll adapter &

pressure Test adapter &

ller

2-60-A0006

00367

TUBE TOOLS - BUMPER BOAT

Part#

Description

Price

2-60-0046

Gauge, Low Pressure 0-15 (Used for Super Tube)

$58.00

3-96-0024

NLA/Gauge, Low Pressure 0-15 (Super Tube & Poly Tube(Motion

$95.00

00367

Filler, Super-Tube Plastic Type

$8.86

2-60-A0006

Filler, Super Tube (Use ST Cap and Valve) Fill Super Tubes

$16.83

2-60-0124

Tool, In

ator/De

ator Super Tube 4.0hp 130cfm

$199.00

2-60-0123

Tool, Super Tube Valve Tightener (Plastic Style)

$5.56

#2-60-0124

ate or de

ate tubes in

no time at all with this 4

hp vacuum/blower

Summary of Contents for 24v 1750 rpm












































































































































































Search results

Summary of Contents for 24v 1750 rpm

Reviews:

Related manuals for 24v 1750 rpm

Brands by name

Popular brands

J&J Amusements 24v 1750 rpm, Service Manual

Search results

Summary of Contents for 24v 1750 rpm

Reviews:

Related manuals for 24v 1750 rpm

Brands by name

Popular brands