J&J Amusements 24v 1750 rpm Service Manual Download Page 29

Page: 29 / 171

IC
A

IO
N

Specifi cations and prices subject to change without notice. Download latest update to this manual on-line.

Install the “RED” cable from the breaker to

the positive post of battery #4.

Install the “BLACK” cable from the negative main

power post to the negative post of battery #1.

Carefully remove the wooden prop rod, place inside the

hull, and lower the boat top until it’s fully closed.

Check the volt meter display.

If the meter is not displaying 24 volts, check the breaker.

If the breaker is “on”, then the battery wiring will need to be rechecked.

Battery 4

Battery 3

Battery 1

Battery 2

Battery 3

Battery 1

Battery 2

Summary of Contents for 24v 1750 rpm












































































































































































Search results

Summary of Contents for 24v 1750 rpm

Reviews:

Related manuals for 24v 1750 rpm

Brands by name

Popular brands

J&J Amusements 24v 1750 rpm, Service Manual

Search results

Summary of Contents for 24v 1750 rpm

Reviews:

Related manuals for 24v 1750 rpm

Brands by name

Popular brands