background image

phone: 1-800-854-3140 | 1-503-304-8899   fax: 1-800-366-7505 | 1-503-304-1899   www.jjamusements.com

5-1

ENGINE ASSEMBLY

General Information .............................................................5-1

Handle bar ............................................................................. 5-2

Pivot.......................................................................... 5-3

Prop guard................................................................. 5-4

The Honda BF2.3D engine was chosen for its reputation for dependable service and its 

reduced emissions (less smoke and less oil in the water), this motor quietly performs. 

Initially designed for use in the corrosive marine environment, this dependable unit has 

been modi

fi

 ed to be controlled from behind and transformed to operate in the bumper 

boat. This section will go over the components that J&J installs only. 

“Refer to the Honda shop manual for repairing, troubleshooting and maintaning the 

engine.”

 

NOTE:

YOU COULD:

 VOID WARRANTY if these instructions are not followed.

CHECK & ADD OIL DAILY!

If correct oil isn’t added on a daily basis, motor will seize up. Observe proper method. 

(see Honda service manual)

CHECK AND/OR ADD OIL TO GEAR CASE BEFORE STARTING.

Check every week or every 200 operating hours. 

Observe proper method. 

(see Honda service manual)

HONDA BF2.3D MOTOR BREAK-IN PROCEDURE.

Like all motors the BF2.3 needs to be broken in well to ensure a long trouble free life.

Please follow these starting instructions to help the process.

1. 

Lift the motor cover and turn the chrome limiter cap on the side of the carburetor back and forth 6 to 8 times to break 

lose any dry gas that may have formed during storage. Turn the limiter cap all the way to the left.

2. 

 Pull the choke and start the motor. Once running close the choke and run the motor at high rpms varying the speed 

for a good 10 minutes.

3. 

While running adjust the idle adjustment screw (located on back of carburetor) to increase the idle speed just short of 

engaging the clutch. As the motor breaks in you will have to adjust the idle down.

PULL STARTER ROPE STRAIGHT OUT.

If the starter rope is pulled to hard, straight up or to one side, the starter will break.

Read all manuals before starting! 

Owners, Shop and J&J Manuals!

Careless operation or misuse may cause injury and/or motor damage. If any of the above are not followed, WARRANTY 

COULD BE DENIED! It is very easy for Honda ®  dealers to tell if you did not observe instructions. Please adhere to all 

warnings, notices, dangers and, cautions. Read and understand manuals before operating.

Summary of Contents for 24v 1750 rpm












































































































































































Reviews: