GD350A series high-performance multifunction VFD
-45-
including delete, shift-up and shift-down; the addition function can be set in a certain function code of
a function group. The edit function is shown in the figure below.
01: GD350A
16:02:35 Forward
Local
Ready
Edit
Return
Select
P00.10
：
Keypad setting frequency
P00.00
：
Speed control mode
P00.11
：
Acceleration time 1
P00.12
：
Deceleration time 1
P00.01
：
Running command channel
P00.13
：
Running direction selection
01: GD350A
16:02:35 Forward
Local
Ready
Homepage
Return
Select
Common parameter
setup
Parameter setup
State monitoring/fault
record
Motor parameter
autotuning
Parameter backup/restore
to default value
System setting
01: GD350A
16:02:35 Forward
Local
Ready
Homepage
Return
Select
Shift up
Shift down
Delete from the list
Figure 5.12 List edit diagram 3
5.4.3 Add parameters to the parameter list displayed in stop/running state
In the fourth-level menu of "State monitoring", the parameters in the list can be added to the "parameter
displayed in stop state" list or "parameter displayed in running state" list as shown below.
01: GD350A
16:02:35
Homepage
Return
Confirm
Add to the parameter list displayed in stop state
01: GD350A
16:02:35 Forward
Local
Ready
Add
Return
Select
P17.00
：
Setting frequency
P17.01
：
Output frequency
P17.02
：
Ramps reference frequency
P17.03
：
Output voltage
P17.04
：
Output current
P17.05
：
Motor speed
Add to the parameter list displayed in running state
01: GD350A
16:02:35
Sure to add to the parameter list
displayed in stop state?
Forward
Local
Ready
Forward
Local
Ready
Homepage
Return
Confirm
01
：
GD350
16:02:35
主页
返回
确定
添加到停机状态显示参数
01
：
GD350
16:02:35
添加
返回
选择
P17.00:
设定频率
P17.01
：输出频率
P17.02
：斜坡给定频率
P17.03
：输出电压
P17.04
：输出电流
P17.05
：电机转速
添加到运行状态显示参数
01
：
GD350
16:02:35
主页
返回
确定
确认添加到运行状态显示参数？
Forward
Local
Ready
01
：
GD350
16:02:35
主页
返回
确定
添加到停机状态显示参数
01
：
GD350
16:02:35
添加
返回
选择
P17.00:
设定频率
P17.01
：输出频率
P17.02
：斜坡给定频率
P17.03
：输出电压
P17.04
：输出电流
P17.05
：电机转速
添加到运行状态显示参数
01
：
GD350
16:02:35
主页
返回
确定
确认添加到运行状态显示参数？
Forward
Local
Ready
01
：
GD350
16:02:35
主页
返回
确定
添加到停机状态显示参数
01
：
GD350
16:02:35
添加
返回
选择
P17.00:
设定频率
P17.01
：输出频率
P17.02
：斜坡给定频率
P17.03
：输出电压
P17.04
：输出电流
P17.05
：电机转速
添加到运行状态显示参数
01
：
GD350
16:02:35
主页
返回
确定
确认添加到运行状态显示参数？
Forward
Local
Ready
01: GD350A
16:02:35
Homepage
Return
Confirm
Add to the parameter list displayed in stop state
01: GD350A
16:02:35
Add
Return
Select
P17.00
：
Setting frequency
P17.01
：
Output frequency
P17.02
：
Ramps reference frequency
P17.03
：
Output voltage
P17.04
：
Output current
P17.05
：
Motor speed
Add to the parameter list displayed in running state
01: GD350A
16:02:35
Homepage
Return
Confirm
Sure to add to the parameter list
displayed in running state?
Forward
Local
Ready
Forward
Local
Ready
Forward
Local
Ready
Figure 5.13 Add parameter diagram 1
Press
key to enter parameter addition interface, select the operation needed, and press
key,
key or
key to confirm the addition operation. If this parameter is not included in
the "parameter displayed in stop state" list or "parameter displayed in running state" list, the parameter
added will be at the end of the list; if the parameter is already in the "parameter displayed in stop state"
list or "parameter displayed in running state" list, the addition operation will be invalid. If
key or
key is pressed without selecting addition peration in "Addition" interface, it will
return to monitoring parameter list menu.
Part of the monitoring parameters in P07 HMI group can be added to the "parameter displayed in stop
state" list or "parameter displayed in running state" list; All the parameters in P17, P18 and P19 group
can be added to the "parameter displayed in stop state" list or "parameter displayed in running state"
list.
Up to 16 monitoring parameters can be added to the "parameter displayed in stop state" list; and up
to 32 monitoring parameters can be added to the "parameter displayed in running state" list.
