manualshive.com logo in svg

Epson S1C31D50, Technical Instructions

The Epson S1C31D50 is an advanced microcontroller requiring detailed technical instructions for optimal usage. Our website provides a free and easily accessible manual download. Discover all the features and functions of this powerful product by downloading the user manual from manualshive.com and unlock its full potential.

Share
Download
background image

6-10

 

Seiko Epson Corporation

 

S1C31D50 TECHNICAL MANUAL

 

(Rev. 1.00)

 

 

 

DMA transfer procedure

 

 

1.

 

Configure the data structure table for scatter-gather transfer. 
Set the cycle_ctrl for the last task to 0x1 and those for other tasks to 0x5. 

2.

 

Start data transfer by following the procedure shown in Section 6.2.1, 

“Initialization

.

”

 In Step 2 of 

the initialization procedure, configure the primary data structure with the control data shown 
below. 

Transfer source end pointer = Data structure table end address 
Transfer destination end pointer = Alternate data structure end address 
dst_inc = 0x2 
dst_size = 0x2 
src_inc = 0x2 
src_size = 0x2 
R_power = 0x2 
n_minus_1 = Number of tasks × 4 - 1 
cycle_ctrl = 0x4 

3.

 

The DMA transfer is completed when a DMA transfer completion interrupt occurs. 

 

 

 

Summary of Contents for S1C31D50

























































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for S1C31D50

HANYOUNG NUX TS500 Manual preview
TS500
Brand: HANYOUNG NUX Pages: 56
ICM Controls ICM330 Manual preview
ICM330
Brand: ICM Controls Pages: 2
ICM Controls ICM2909 Manual preview
ICM2909
Brand: ICM Controls Pages: 2
U.S. Divers Impulse Service & Repair Manual preview
Impulse
Brand: U.S. Divers Pages: 22
Unimig UNI-FLAME REG Operation Manual preview
UNI-FLAME REG
Brand: Unimig Pages: 4
Velleman-Kit EDU01 Manual preview
EDU01
Brand: Velleman-Kit Pages: 32
Zamel RTS-01A Instruction Manual preview
RTS-01A
Brand: Zamel Pages: 2
Ulvac UK-2 Instruction Manual preview
UK-2
Brand: Ulvac Pages: 48
Cameron CLIF MOCK CD-20SFA User Manual preview
CLIF MOCK CD-20SFA
Brand: Cameron Pages: 12
Eaton EM4-201-DX2 Installation Instructions Manual preview
EM4-201-DX2
Brand: Eaton Pages: 9
THOMSON Electrak GX Installation Manual preview
Electrak GX
Brand: THOMSON Pages: 18
EFI E-36A Installation And Service Manual preview
E-36A
Brand: EFI Pages: 129
Toky TP-C Series User Manual preview
TP-C Series
Brand: Toky Pages: 4
X10 Sundowner SD533 Owner'S Manual preview
Sundowner SD533
Brand: X10 Pages: 3
Infineon XC800 AP08113 Application Note preview
XC800 AP08113
Brand: Infineon Pages: 22
Isonas Pure IP Wiegand Reader Quick Installation Instructions preview
Pure IP Wiegand Reader
Brand: Isonas Pages: 2
Intec Controls PolyGard 2 DC6 User Manual preview
PolyGard 2 DC6
Brand: Intec Controls Pages: 17
OMC AP23 Installation, Operation And Maintenance Manual preview
AP23
Brand: OMC Pages: 12

Brands by name

Popular brands

Load more brands