Epson S1C31D50 Technical Instructions Download Page 264

Page: 264 / 472

16-26

Seiko Epson Corporation

S1C31D50 TECHNICAL MANUAL

(Rev. 1.00)

I2C Ch.

Interrupt Enable Register

Register name

Bit

Bit name

Initial

Reset

R/W

Remarks

I2C_

INTE

–

0x00

–

BYTEENDIE

R/W

GCIE

R/W

NACKIE

R/W

STOPIE

R/W

STARTIE

R/W

ERRIE

R/W

RBFIE

R/W

TBEIE

R/W

Bits 15

–

Reserved

Bit 7

BYTEENDIE

Bit 6

GCIE

Bit 5

NACKIE

Bit 4

STOPIE

Bit 3

STARTIE

Bit 2

ERRIE

Bit 1

RBFIE

Bit 0

TBEIE

These bits enable I2C interrupts.

1 (R/W): Enable interrupts
0 (R/W): Disable interrupts

The following shows the correspondence between the bit and interrupt:
I2C_

INTE.BYTEENDIE bit: End of transfer interrupt

I2C_

INTE.GCIE bit:

General call address reception interrupt

I2C_

INTE.NACKIE bit:

NACK reception interrupt

I2C_

INTE.STOPIE bit:

STOP condition interrupt

I2C_

INTE.STARTIE bit:

START condition interrupt

I2C_

INTE.ERRIE bit:

Error detection interrupt

I2C_

INTE.RBFIE bit:

Receive buffer full interrupt

I2C_

INTE.TBEIE bit:

Transmit buffer empty interrupt

I2C Ch.

Transmit Buffer Empty DMA Request Enable Register

Register name

Bit

Bit name

Initial

Reset

R/W

Remarks

I2C_

TBEDMAEN

–

TBEDMAEN[15:0]

0x0000

R/W

–

Bits 15

–

TBEDMAEN[15:0]

These bits enable the I2C to issue a DMA transfer request to the corresponding DMA
controller channel (Ch.0

–

Ch.15) when a transmit buffer empty state has occurred.

1 (R/W): Enable DMA transfer request
0 (R/W): Disable DMA transfer request

Each bit corresponds to a DMA controller channel. The high-order bits for the
unimplemented channels are ineffective.

Summary of Contents for S1C31D50

























































































































































































































































































































































































































































































Search results

Summary of Contents for S1C31D50

Reviews:

Epson S1C31D50, Technical Instructions, Page: 264 / 472

Search results

Summary of Contents for S1C31D50

Reviews: