Dell 6 series User Manual Download Page 87

Page: 87 / 160

Configuring and Managing RAID

Perform the following steps to select the virtual disk parameters:

Press <Tab> to move the cursor to the parameters you want
to change.

Press the down-arrow key to open the parameters and scroll down the
list of settings.

To change the stripe element size, press <Tab> to highlight

Stripe

Element Size

Press <Enter> to display the list of stripe element sizes (

8 KB

16 KB

32 KB

64 KB

128 KB

256 KB

512 KB

, and

1024 KB

). Press the

down-arrow key to highlight the desired option and press <Enter>.
The default is

64 KB

If you need to change the read policy, press <Tab> to move the cursor
to

Read Policy

Press <Enter> to display the options (

No Read Ahead

Read Ahead

Adaptive Read Ahead

). Press the down-arrow key to highlight the

desired option and press <Enter>.

If you need to change the write policy, press <Tab> to move the
cursor to

Write Policy

Press <Enter> to display the options (

Write-Through

Write Back

Press the down-arrow key to highlight an option and press <Enter>.

Press <Tab> to move the cursor to

Force WB with no battery

and

press <Enter>. If you chose

Write-Through

as the write policy, then

this option is not available.

Press <Tab> to move the cursor to

Initialize

and press <Enter>.

CAUTION:

Do not initialize virtual disks when attempting to recreate an existing

configuration.

NOTE:

The initialization performed at this stage is fast initialization.

Press <Tab> to move the cursor to

Configure HotSpare

and press

<Enter>.

NOTE:

The hot spare created at this stage is a dedicated hot spare.

Dell_PERC6.2_UG.book Page 87 Wednesday, June 24, 2009 6:08 PM

Summary of Contents for 6 series

































































































































































Search results

Summary of Contents for 6 series

Reviews:

Related manuals for 6 series

Brands by name

Popular brands

Dell 6 series, User Manual

Search results

Summary of Contents for 6 series

Reviews:

Related manuals for 6 series

Brands by name

Popular brands