Dell 6 series User Manual Download Page 20

Page: 20 / 160

Overview

Figure 2-3.

Example of Distributed Parity (RAID 5)

NOTE:

Parity is distributed across multiple physical disks in the disk group.

Figure 2-4.

Example of Dual Distributed Parity (RAID 6)

NOTE:

Parity is distributed across all drives in the array.

Stripe element 1
Stripe element 7

Stripe element 2
Stripe element 8

Stripe element 3
Stripe element 9

Stripe element 4
Stripe element 10

Stripe element 5

Parity (6–10)

Parity (11–15)

Parity (1–5)
Stripe element 6
Stripe element 12

Stripe element 15

Stripe element 11

Stripe element 14

Stripe element 13
Stripe element 19
Stripe element 25

Stripe element 20

Stripe element 23

Stripe element 18

Stripe element 21

Stripe element 16

Stripe element 22

Stripe element 17

Parity (21–25)

Parity (26–30)

Parity (16–20)

Stripe element 24
Stripe element 30

Stripe element 27

Stripe element 29

Stripe element 26

Stripe element 28

Stripe element 1

Stripe element 5

Stripe element 2

Stripe element 6

Stripe element 3

Parity (5–8)

Stripe element 4

Parity (5–8)

Parity (1–4)

Stripe element 7

Stripe element 10

Parity (1–4)

Stripe element 8

Stripe element 12

Stripe element 9

Stripe element 11

Parity (9–12)

Stripe element 13 Stripe element 14

Stripe element 16

Parity (13–16)

Stripe element 15

Parity (13–16)

Dell_PERC6.2_UG.book Page 20 Wednesday, June 24, 2009 6:08 PM

Summary of Contents for 6 series

































































































































































Search results

Summary of Contents for 6 series

Reviews:

Related manuals for 6 series

Brands by name

Popular brands

Dell 6 series, User Manual

Search results

Summary of Contents for 6 series

Reviews:

Related manuals for 6 series

Brands by name

Popular brands