Dell 6 series User Manual Download Page 110

Page: 110 / 160

110

Configuring and Managing RAID

After you enable the BIOS for a controller, perform the following steps to
enable the boot support for that controller.

Press <Ctrl><N> to access the

Ctrl Mgmt

menu screen.

Press <Tab> to move the cursor to the

Select Bootable VD

in the

Settings

box.

Press the down-arrow key to display a list of virtual disks.

Use the down-arrow key to highlight a virtual disk.

Press <Enter> to select the virtual disk.

Press <Tab> to move the cursor to the

Apply

button, and then press

<Enter> to apply the selection.
Boot support is enabled for the selected controller.

Enabling BIOS Stop on Error

The option

BIOS Stop on Error

is used to stop the system from booting if

there are BIOS errors. Perform the following steps to enable

BIOS Stop on

Error

Press <Ctrl><N> to access the

Ctrl Mgmt

menu screen.

Press <Tab> to move the cursor to

Enable BIOS Stop on Error

in the

Settings

box.

Press the spacebar to select

Enable BIOS Stop on Error

displays beside

Enable BIOS Stop on Error

Press <Tab> to move the cursor to the

Apply

button, and then press

<Enter> to apply the selection.
The controller BIOS is enabled. To disable

Enable BIOS Stop on Error

use the spacebar to de-select

Enable BIOS Stop on Error

, then select

Apply

and press <Enter>.

Dell_PERC6.2_UG.book Page 110 Wednesday, June 24, 2009 6:08 PM

Summary of Contents for 6 series

































































































































































Search results

Summary of Contents for 6 series

Reviews:

Related manuals for 6 series

Brands by name

Popular brands

Dell 6 series, User Manual

Search results

Summary of Contents for 6 series

Reviews:

Related manuals for 6 series

Brands by name

Popular brands