Dell 6 series User Manual Download Page 60

Page: 60 / 160

Installing and Configuring Hardware

Figure 4-14.

Removing and Installing the Storage Controller Card

Installing the Storage Controller Card

To install your new storage controller card:

Unpack the new storage controller card and check for damage.

NOTE:

If the card is damaged, contact Dell technical support.

Place the storage controller card onto the system board. Align the storage
controller card such that the tabs on the system board tray fit through the
notches on the edges of the storage controller card.

Slide the storage controller card towards the connector on the system
board until the storage controller clicks in place.

Reinstall the system board. For more information on reinstalling the
system board, see your system’s

Hardware Owner’s Manual

or the

User’s Guide

release lever

storage controller card

Dell_PERC6.2_UG.book Page 60 Wednesday, June 24, 2009 6:08 PM

Summary of Contents for 6 series

































































































































































Search results

Summary of Contents for 6 series

Reviews:

Related manuals for 6 series

Brands by name

Popular brands

Dell 6 series, User Manual

Search results

Summary of Contents for 6 series

Reviews:

Related manuals for 6 series

Brands by name

Popular brands